Ace Automated Gates | Austin

Hiring one automatic gate installer for the whole build means you don’t have to work around anything. We design the gate, posts, operator, access control, safety devices, and power together, rather than inheriting them piecemeal from someone else.

We’ll come and look at the entrance before recommending anything. Arrange a site visit or call (512) 236-5178, and if the existing gate prompted this, replacing it is its own decision or call (512) 236-5178.

Submit this form to request quote

  • This field is for validation purposes and should be left unchanged.
gate post footing austin tx 01 by Ace Automated Gates Austin

What decides the design

Picking an operator is only one part of designing a gate that works, and it’s rarely the first part.

The opening comes first: its width, the driveway grade, where vehicles need to stop, and how much room a panel has to move through. Rock, slope, drainage, existing concrete, and underground utilities all narrow the options before anyone talks about hardware. So does the simple question of whether a panel has room to swing, which usually drives the decision between the two systems and is worth understanding before you settle on a configuration that suits the opening.

Wind matters more than most people expect. A large, solid driveway gate catches a lot of it, and that load runs through the panel, posts, hardware, and operator every time the weather turns. Those four things must be specified to work together, which is why a design that works at ten feet doesn’t simply scale to sixteen.

What holds the gate up

We don’t use one post depth for every gate, and we’d be suspicious of anyone who does.

Gate size and weight, configuration, post size, soil conditions, wind exposure, and the equipment going on it all affect the foundation. A driveway gate loads a post very differently from a pedestrian gate. With a large swing gate, we support the panel’s weight and the forces it generates every time it starts, stops, and changes direction, a load that arrives thousands of times a year.

Ground conditions change across the metro. In western Austin, we may be into limestone or caliche. In areas with expansive clay, we’re building for movement rather than pretending it won’t happen. We size the foundation around the actual gate and the actual site instead of digging the same hole everywhere.

This determines whether the gate is still hanging true in year five, and it’s entirely invisible once the work is finished. It’s also the reason so much repair work on existing gates traces back to a post rather than a motor.

Automatic gate repair underway on a residential driveway gate in Austin TX

HOA approval comes before fabrication

We’ve worked throughout the Austin metro in HOA-controlled and gated communities, and what they require varies more than people assume.

Restrictions have covered gate appearance, materials, height, placement, architectural style, and what’s visible from the street. Practical constraints go beyond appearance too: where the gate moves, where vehicles wait while it opens, access for deliveries and visitors, emergency access where it applies, and where the operator and controls can physically go.

We want approval in hand before we build, and the cost guide is worth reading first so the design you submit is one you would actually fund. Changing a gate design on paper takes a phone call. Changing a fabricated and installed driveway gate because the HOA turned it down is a different conversation entirely, and not one anybody enjoys.

Getting power to the gate

Where mains power can reach the entrance sensibly, we trench for it as part of the install.

Where it can’t, solar power at the entrance is often the better answer, particularly on acreage where the gate sits far from the nearest supply. Solar works well for driveway gates when it’s designed around the gate and how it’s actually used. That means panel location and sun exposure, battery capacity, and an honest estimate of how many times a day the gate will cycle, because a system sized for light use will struggle the moment reality exceeds the assumption.

The same visit settles how people get through: keypads, remotes, phone-based access, intercoms, or a resident directory, depending on how many people need through and who they are.

hill-country-slide-gate-stone-columns-automatic-gates-austin-04

What the process looks like

Site visit, then design, then fabrication, then installation, then commissioning.

We weld the panel in steel or iron to your opening, rather than ordering it to the nearest standard width. Posts and footings go in and cure before we hang anything on them. Then the panel, the operator that drives it, the safety devices, and the controls, followed by enough cycles on site to find problems while we’re still standing there.

The work carries a one-year craftsmanship warranty; we’ve been building gates here since 2013, and we’re fully insured. If a job needs a new circuit or panel work, we bring in a licensed electrician rather than improvise.

Most of what we build falls into residential driveway gates and commercial installations, with acreage entrances sitting between the two and borrowing from both.

If you’re still choosing a residential design, or you want a sense of the numbers before committing, we have a guide to what it is likely to cost that will tell you whether the figures in front of you are reasonable.

Where we build

Ace Automated Gates | Austin builds from 1821 Heatherglen Ln, Austin, TX 78758, across the metro and surrounding cities.

Customers are usually surprised by how many parts must agree for a gate to open reliably: the panel, the posts, the hinges or rollers, the operator, the power, the controls, the safety devices, the driveway grade, and where a vehicle actually stops. Looking at the whole entrance, rather than picking equipment from a catalog, is the only way to get it right. You can see gates we’ve built, and picking a residential design covers the choices most homeowners face and gives you a sense of the finish. Call (512) 236-5178 and describe the opening.

Frequently Asked Questions

Groundwork rather than fabrication sets it. Footings have to cure properly before anything gets hung on them, so a typical driveway job runs across more than one visit rather than a single day. Long approaches that need a trench for power add time again, and HOA approval usually adds more than either.

We weld our own, in steel or iron, sized to your opening. That matters most when the opening isn’t a round number or the drive doesn’t sit level, since a stock panel forced into an awkward entrance is where sagging and binding start a few years later, long after the installer has gone.

Room, mostly. A swing panel needs clear space to arc into, and on a short drive, a rising approach, or a curve near the opening, that space simply does not exist. Where it does exist, swing systems are simpler and cheaper to automate, which means availability decides the question far more often than budget does.

More than most people expect, and no two are identical. Panel weight, configuration, post size, soil conditions, wind exposure, and the operator being fitted all change the specification. A large swing gate is supported against its own weight plus the forces generated every time it starts, stops, and reverses direction.

Yes. Where trenching several hundred feet through rock is impractical, solar power at the entrance does the same job from a panel and a battery. Size it against real cycle counts rather than an optimistic estimate, or the system quietly becomes the next problem you call us about.

In most controlled communities, yes, and we want it in hand before we start any fabrication. Restrictions typically cover appearance, materials, height, placement, and what’s visible from the street. Changing a drawing is easy and costs nothing. Changing a finished gate that has already been set in concrete is not.

We set or check the posts, hang the panel, mount and wire the operator, then commission the safety devices and entry hardware. After that, we cycle the gate enough times on site to find the problems while we are still standing there, rather than leaving you to discover them next week.

Scroll to Top